Hioki MR8827 Instruction Manual Download Page 92

Page: 92 / 436

Save Data

Example 5

Saving data in an existing folder on the media using divided saving

Save to

CF:¥HIOKI_

MR8827¥TEST

Save method

Normal Save

Folder to save Off

(Create a folder named “TEST” on the CF card

beforehand.)

When the storage media is full:

Automatic saving stop.

Example 6

Saving data in an automatically created folder on storage media using divided saving

Save to

CF:¥HIOKI_

MR8827

Save method

Normal Save

Folder to save On

When the storage media is full:

Automatic saving stop.

Save Operations (When Setting the Save Destination to

[LAN]

)

The file is saved according to the method (on the

right figure) specified under

[Save Settings]

using

the 9333 LAN Communicator.

For more information about how to configure save

settings, refer to the instruction manual for the 9333

LAN Communicator.

The destination folders and files are named in the

previously-determined formats and saved as follows:

Specified folder

192.168.1.1

14-01-10

14-01-11

HIOKI 9333

File names will be

“WAVE + hours/

minutes/seconds.”

Waveform files

14-01-20

14-01-21

File names will be

“PRA

number.”

Folder names

will be

“YY-MM-DD.”

File names will be

“WAVE + hours/

minutes/seconds.”

WAVE124012.BMP

Numerical calculation files

PARAMETER.TXT

PARAMETER_1.TXT

WAVE123015.MEM

WAVE123245.MEM

WAVE123245.TXT

Folder name

will be Model

MR8827 IP

address.

TEST

0000AUTO.IDX

0001AUTO.MEM

0001TEST

Up to 5,000 files

0000AUTO.IDX

0000AUTO

0001AUTO

Up to 5,000 folders

0000AUTO.MEM

The automatically created folder will be

named “4-digit folder name.”

0000AUTO

(A new folder will be created automatically when 5,000

folders have been saved in the TEST folder.)

HIOKI_MR8827

AUTO014530

0000AUTO.IDX

0001AUTO.MEM

0001AUTO014530

(A new folder will be created automatically when 5,000 folders

have been saved in the AUTO014530 folder.)

Up to 5,000 files

0000AUTO.IDX

0000AUTO

0001AUTO

Up to 5,000 folders

0000AUTO.MEM

“AUTO + hours/minutes/seconds”

is created automatically. (Example: 1:45:30)

Folder name created next will be

“4-digit folder name.”

0000AUTO

HIOKI_MR8827

Save/Load Data and Manage Files

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands