Hioki MR8827 Instruction Manual Download Page 256

Page: 256 / 436

251

FFT Analysis Condition Settings

13.3.6

Analysis Result Peak Value Settings

You can display local or global maxima ([maximal]/ [maximum]) of the input signal and analysis results

on the Waveform screen. However, if Nyquist display is selected on the Status screen-

[Status]

sheet, no

peak values are displayed.

Procedure

Press the

STATUS

key to open the Status screen, and then select the

[Status]

sheet.

To select peak value display.

Move the cursor to

[Peak]

Off

Not displayed.

(Default setting)

Maximal (local maxima)

When the value of data at a point is greater than that of the

adjacent points, that point is considered a local maximum.

The ten largest local maxima are displayed.

Maximum (global maxima)

Among all data values, the ten points with the greatest

values are displayed.

Maximal

Maximum

• No maxima will be displayed if peak values cannot be detected.

• Peak values on the Waveform screen can be displayed and printed, but cannot be saved as peak

values in text files.

• Depending on the split screen status, it may not be possible to display ten peak values. In such

cases, as many items as possible will be displayed, starting from the largest item.

Example: When the reference data setting is

[From Memory]

Peak value display

From 1 to 4

FFT
Function

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands