Hioki MR8827 Instruction Manual Download Page 21

Page: 21 / 436

Part Names and Functions

1.2 Part Names and Functions

Top

Model U8350 Printer Unit

(Optional)

USB connector (Type A)

Connect USB memory stick and

USB mouse here. (p. 40)

POWER switch (p. 45)

Front Side

Operation key (p. 17)

Display

CF card slot

Handle

Back Side

100BASE-TX connector

Connect LAN cable here.

(p. 309)

USB connector

(Type B)

Connect to the

computer (PC)

with the USB

cable.

(p. 328)

GND terminal

(Functional earth terminal)

Connect to Earth ground. (p. 44)

External control terminals

An external sampling signal can

be connected here. (p. 335)

Allows control of the unit.

Standard LOGIC terminals

Input connectors for optional

proprietary logic probes.

(p. 28)

Various modules

(p. 26), (p. 28)

(For details, see the instruction manual

of the respective module.)

Power inlet

Connect the supplied power

cord here. (p. 44)

Serial No.

Do not remove

this label, as it

is required for

product support.

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands