Hioki MR8827 Instruction Manual Download Page 138 | Manualshive

Page: 138 / 436

background image

133

Monitor Input Levels (Level Monitor)

7.6 Monitor Input Levels (Level Monitor)

7.6.1

Level Monitor

All input waveform levels can be monitored in real time.

Analog channels and logic channels can be displayed at the same time.

Procedure

Press

DISP

to open the Menu → Display Menu

Selecting

[Monitor]

brings up the analog

channel level display in the left part of the

Waveform screen, and the logic channel

level display in the right side of the

Waveform screen.

To hide the level monitor

Select

[Monitor]

again.

Analog channel

level display

Monitor values of analog and logic

channels

Display Menu

Display format 2 - 16 screens (p. 59)

Level monitors are displayed for each

graph.

Upper and lower limit indication is combined

with level monitor.

Refer to “7.7.1 Show Upper/Lower Limit on

Waveform Screen” (p. 136).

Logic channel

level display

How to Interpret Level Monitors

Analog channel level display

High

High & Low

Low

Input

level

Waveform Display

Range Full Span

Logic channel level display

When the display setting is On,
the part indicated in white takes
the color specified for the
waveform display. When the setting
is Off, the part becomes gray.
The part indicated in black is
the background color.

•

Input levels are not displayed for channels that have no corresponding module installed.

•

Channels higher than the number specified for

[Used Ch]

do not display analog input levels.

(Example: When

[Used Ch]

is set to

[Ch4]

, the levels for CH3 to Ch16 and Ch19 to Ch32 are not

displayed.)

7

W

avef
orm Screen Monit

oring and

Analysis

«
...
136
137
138
139
140
...
»

Summary of Contents for MR8827





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR8827

Brand: ABB Pages: 86

Brand: GALLERY Pages: 18

MicroVersaTrip Plus

Brand: GE Pages: 20

Brand: GE Pages: 252

Brand: Balanced Body Pages: 12

Brand: Eagle Pro Pages: 6

Brand: GE Pages: 10

Brand: OMCA Pages: 36

Brand: Salford Pages: 64

Brand: Ace Pages: 17

Brand: ACE INSTRUMENTS Pages: 33

Brand: ACE INSTRUMENTS Pages: 2

Brand: ACE INSTRUMENTS Pages: 2

Brand: TapFlo Pages: 35

Brand: DANA Pages: 8

Brand: 2E Pages: 6

Brand: Backyard Discovery Pages: 51

Brand: Nautilus Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands