Hioki MR8827 Instruction Manual Download Page 271

Page: 271 / 436

266

Screen Display Settings

Procedure

Press the

DISP

key to open the Waveform screen.

To stop waveform movement during measurement

Wavefor movement can be stopped temporarily

by pressing the

AUTO

key during measurement.

The latest calculation results are displayed in

the foreground.

To restart, press the

AUTO

key again.

The latest waveform displayed during

pausing of measurement

Past waveforms

To read measurement values of past waveforms with the cursor

After measurement is finished, the values of each waveform can be read using the cursor.

Press the

WAVE

key on the panel

of the unit.

Select a waveform.

Use the jog and shuttle knobs to

select the waveform.

(The waveform number is displayed in the

lower right of the screen.)

Move the cursor.

Press the

AB CSR

key, then rotate

the jog and shuttle to read the cursor

value.

Older waveforms have

larger numbers.

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands