Hioki MR8827 Instruction Manual Download Page 324

Page: 324 / 436

319

Perform Remote Operations on the Instrument (Use an Internet Browser)

Download Memory Data From the unit

You can download measured data.

The data format can be binary, text, or Excel*.

* Microsoft Excel

Measured Data Download Screen

Click

[Start/Stop]

in the list of operations to open the screen.

Procedure

Start measurement.

Stop measurement.

Select one of the options below

the measured data display.

Get binary data Retrieve binary data.
Get text data

Retrieve text data.

To MS Excel

Display data in Excel. cursors. (Data can be

opened with Microsoft Excel)

•

It may not be possible to retrieve data when JRE has not been installed on your PC. (p. 315)

• You cannot download measured data during measurement. Stop measurement and then download

data.

• When you use Internet Explorer and press

[To MS EXCEL]

and select

[Open]

, an error may occur

during transmission. In such a case, select

[Save]

Connect to a PC

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands