Hioki MR8827 Instruction Manual Download Page 288

Page: 288 / 436

283

FFT Analysis Modes

Auto-correlation Function

Shows the correlation of two points on the input signal at time differential

Main uses:

• To detect periodicity in irregular signals (improving and detecting SNR)

• To inspect periodic components in a noisy waveform.

About the Functions, refer to “13.9.2 Analysis Mode Functions” (p. 289).

Axis

Display type

Description

X axis

Linear

Time display

The center (

= 0) is the reference. To the right is lag time (+

t), and to the left is

lead time (-

Y axis

Lin-Mag

+1 to −1 (dimensionless units)

The closest correlation at time differential

is +1, and the least correlation is 0.

−1 indicates completely reversed polarity.

Because of the characteristics of the function,

= 0 b1.

Waveform Example

X axis: Linear

Y axis: Lin-Mag

This instrument provides a circular auto-correlation function. Analysis results are normalized to the

maximum value.

FFT
Function

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands