Hioki MR8827 Instruction Manual Download Page 39

Page: 39 / 436

Connection Cables

Measuring current

Connect Model 9318 Conversion Cable to

the module jack.

Connect with: Clamp sensors

•Model 9272-10

Clamp on Sensor

•Models 9709, CT6862,

CT6863, CT6865

AC/DC Current Sensor

•Models CT6841, CT6843,

CT6844, CT6845

AC/DC Current Probe

Example:

Model 9272-10 + Model 9318

Applicable Modules

•

Model 8971 Current Unit

To Connect to the Module's Terminals

Example: When connecting Model 9272-10 Clamp on Sensor

Sensor connector

Connect to the measurement

object

Connect the 9318 Conversion Cable

and clamp sensor

Conversion cable plug

Model 9272-10

Conversion Cable

Connector

Clamp sensor

plug

Required tools:

Model 9318 Conversion Cable, Model 9272-10

Clamp on Sensor

Align the grooves of the module’s sensor

connector and the conversion cable plug.

Insert the plug until it locks.

Align the grooves of the conversion cable

connector and the plug of the clamp

sensor to be used. Insert the plug until it

locks.

Connect the clamp sensor to the item to

be measured.

To disconnect the conversion cable

Slide the plug to release the lock and then unplug

the cable.

When Measuring Current With Model 9018-50 Clamp on Probe

When using Model 9018-50 you can use a voltage measurement unit such as Model 8966 Analog Unit to

make current measurements.

For more information about how to configure the instrument for use in this type of application, refer to the

example settings in “8.5.1 Scaling Examples” (p. 153).

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands