Hioki MR8827 Instruction Manual Download Page 153

Page: 153 / 436

148

Display New Waveforms Over Past Waveforms (Overlay)

8.3 Display New Waveforms Over Past Waveforms

(Overlay)

This applies to the Memory function only.

Displayed waveforms are retained on-screen and overlaid with new waveforms.

• Use this to compare new waveforms with those recorded immediately before. (When the trigger mode is

[Repeat]

[Auto]

) (p. 189)

• There are two overlay methods: automatic overlay during measurement and manual overlay.

Normal display

Waveforms with the Overlay Function

Procedure

Press the

STATUS

key to open the Status screen, and then select the

[Status]

sheet.

Move the cursor to

[Overlay].

Off

Overlay disabled.

(Default setting)

Auto

Each time a waveform is acquired, it is automatically

displayed as an overlay.

When the trigger mode is

[Cont.]

[Auto]

, waveforms

will be overlaid from measurement start to stop.

Manual

Overlay waveforms on the screen manually. (See the

next section for the method of overlay.)

This mode cannot be used

simultaneously with Roll Mode.

Refer to “When the overlay function

is enabled ([Auto] or [Manual]).”

(p. 149).

Manual Overlay (Any Waveform Can Be Retained On-Screen)

Press the

DISP

key to open the Waveform screen.

Move the cursor to

[Overlay].

Overlay

(

key)

The loaded waveform on the screen.

The overlay is displayed until the waveform is cleared.

Clear

(

key)

Clears the screen of all overlaid waveforms. Cleared

waveforms cannot be displayed again.

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands