Hioki MR8827 Instruction Manual Download Page 270

Page: 270 / 436

265

Screen Display Settings

13.5.1 Display Running Spectrums

[Format]

is set to

[Running spectrum]

, you can observe changes in frequency over time.

Procedure

Press the

STATUS

key to open the Status screen, and then select the

[Status]

sheet.

Select the reference data.

Move the cursor to

[Reference]

, and select

[New Data]

Select the display format.

Move the cursor to

[Format]

, and select

[

Running

spectrum]

•

[Running spectrum]

can only be set when

[Reference]

[New Data]

• The calculation interval (time interval of the running spectrum waveform and the waveform) is not

regulated.

• Averaging cannot be used.

• Calculations that can be analyzed by running spectrum are limited to the following list. When other

calculations are selected or calculation settings are changed after measurement stops, waveforms

will not be displayed.

(Linear spectrum, RMS spectrum, power spectrum, power spectrum density, LPC analysis, transfer

function, cross power spectrum, 1/1 octave analysis, 1/3 octave analysis)

• When running spectrum is displayed, the auto-saving/auto-printing during measurement cannot be

performed.

FFT
Function

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands