Hioki MR8827 Instruction Manual Download Page 126

Page: 126 / 436

121

Waveform Screen Monitoring

and Analysis

Analytical operations such as display magnification, compression, and search are available on the

Waveform screen. The measurement condition or other configuration can also be changed on this

screen.

To Open the Waveform Screen

A Cursor

Upper limit value

Level Monitor

Lower limit value

B cursor

Scroll bar

Time Value (p. 306)

Press this key.

Operations available from the Waveform screen

AB Cursor

•

Read measurement value (p. 122)

•

Specify a waveform range (p. 125)

Magnify and Compress Waveforms

•

Magnify and Compress Horizontal Axis (Time

Axis) (p. 130)

•

Zoom Function (Magnifying a Section of the

Horizontal Axis (Time Axis) )(p. 131)

•

Magnify and Compress Vertical Axis (Voltage

Axis) (p. 132)

Move the Waveform Display Position

•

Use the jog and shuttle knobs (p. 126)

•

Move the position (p. 127)

Switch the Waveform Screen

(p. 135)

•

Display upper and lower limit values

•Display comments

•

Switch the waveform display width

Perform X-Y Synthesis

(p. 128)

Monitor Input Levels

(p. 133)

7 Waveform Screen Monitoring and Analysis

avef
orm Screen Monit

oring and

Analysis

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands