Hioki MR8827 Instruction Manual Download Page 136

Page: 136 / 436

131

Magnify and Compress Waveforms

7.5.2

Zoom Function

(Magnifying a Section of the Horizontal Axis [Time Axis])

This applies to the Memory function only. A magnified section of a waveform can be displayed together

with the unmagnified view by splitting the screen horizontally.

With the waveform displayed normally on the upper half of the screen, a section magnified along the time

axis can be displayed on the lower half.

Normal Display

Zoomed Display

Normal Display

Zoom

When you press the

PRINT

key while using the Zoom function, the waveform displayed on the lower half of

the screen is printed. (The print format will be as for a single screen waveform. If the AB cursors are used, the

selected section will be printed.)

Procedure

Press the

DISP

key to open the Waveform screen.

Move the cursor to the magnification.

Zoom ratio

waveform

Select

[Zoom On]

The Zoom function is enabled and the screen is split into

upper and lower halves.

(Upper: waveform to be magnified; Lower: magnified
(zoomed) section of waveform)

Select display magnification for the zoomed

waveform section.
Move the cursor to the

[Zoom Mag]

, and set the

magnification.

The zoomed waveform section at the lower half of the

screen is magnified.

When the same value or a smaller value than the

magnification/compression ratio is specified, the ratio is

automatically set to a setting one step higher than the

[Zoom Mag]

setting.

Scrolls the zoomed section of the waveform.

Refer to “7.3.2 Scroll With Jog and Shuttle Knobs

(Scroll)” (p. 126).

To cancel Zoom

Move the cursor to the magnification, and select

[Zoom Off]

. (The condition is canceled while

keeping the inherited zoom ratio.)

Example: When the zoom ratio was set to ×5 and

zoom is canceled, the ratio setting will be

[×5]

Magnifying and

Compressing

ratio waveform

avef
orm Screen Monit

oring and

Analysis

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Hioki MR8827, Instruction Manual, Page: 136 / 436

Search results

Summary of Contents for MR8827

Reviews: