Hioki MR8827 Instruction Manual Download Page 131

Page: 131 / 436

126

Move the Waveform Display Position

7.3 Move the Waveform Display Position

This applies to the Memory and Recorder functions.

7.3.1

About the Display Position

From the scroll bar you can verify the relative position and size of the displayed portion of a waveform

within the overall recorded waveform. Trigger time, trigger position and AB cursor positions (When using

voltage axis cursor or trace cursors) are also displayed.

To verify the display range on the scroll bar

Trigger point

A cursor

B cursor

Blue frame: Screen display range (25 div)

Blue frame: Zoomed display range (lower waveform)

Pink frame: Display range (upper waveform)

Red bar: Recorded waveform

(Gray bar if waveform

is within recording

length)

With zoomed display (p. 131)

7.3.2

Scroll With Jog and Shuttle Knobs (Scroll)

When measuring or displaying an existing waveform, use the jog and shuttle knobs to scroll.

Jog

Shuttle

The scrolling speed is controlled by the rotation angle of the shuttle knob.

Press the

WAVE

key to assign the jog and shuttle knobs to waveform scrolling.

(While the

WAVE

key is lit, the jog and shuttle knobs can be used for scrolling.)

Scroll Direction

Turn CW

Scrolls later on the waveform

from the current point.

Turn CCW

Scrolls earlier on the waveform

from the current point.

Screen Display

Earlier

Later

To see past waveforms in Roll Mode

The jog and shuttle knobs can be used to view past waveforms during measurement.

To redisplay a waveform, select

[Scroll]

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Hioki MR8827, Instruction Manual, Page: 131 / 436

Search results

Summary of Contents for MR8827

Reviews: