Hioki MR8827 Instruction Manual Download Page 132

Page: 132 / 436

127

Move the Waveform Display Position

7.3.3

Change Position (Jump Function)

You can specify the portion to be displayed immediately.

Display location can be specified as follows:

•

Trigger Point

• AB cursor location

•

Specified location (from the beginning [0%] to the end [100%] of the waveform)

50%

100%

75%

25%

Procedure

Press the

DISP

key to open the Waveform screen, and then press the

WAVE

key to open the WAVE settings GUI

displays.

Use the

keys

[←]

[→]

to specify the position.

The yellow frame on the scroll bar indicates the position

to change to.

Select

[Move]

The selected display position appears on the screen.

New position

To move the position when

[Memory Div: On]

with the Memory function

Press the

key

[pos↔block]

. With no block displayed in the upper part of the screen, move the

position.

When a block is displayed in the upper part of the screen, the desired block can be selected and the

recorded waveform can be displayed. (p. 137)

avef
orm Screen Monit

oring and

Analysis

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Hioki MR8827, Instruction Manual, Page: 132 / 436

Search results

Summary of Contents for MR8827

Reviews: