Hioki MR8827 Instruction Manual Download Page 181

Page: 181 / 436

176

Detailed Settings for Modules

Offset

For DC output: Sets DC voltage.

For sine wave output: Sets the offset voltage.

The output voltage with guaranteed accuracy is the sum of the amplitude and the

offset, between -10 V and +10 V. If the sum of the amplitude and the offset is set

outside the guaranteed accuracy range, parts of the waveform will be clamped to the

upper limit, approxi14 V and the lower limit, approximately -14 V.

-10 V to +10 V

When Off

Sets the terminal status when the output is off.

Open

Opens the output terminals, separating them from internal circuits.

Short

Short-circuits the output terminals, separating them from internal circuits.

Output

Turns waveform output On/Off.

Outputs waveform.

Off

Does not output the waveform.

Control

Sets the waveform output.

RUN

Starts output.

PAUSE

Pauses output. While output is paused, the output at the time [PAUSE]

was pressed will be output.

STOP

Stops output.

Method

Selects the control method for waveform output.

Manual

Restricts control of signal output to Signal Generation screen.

Sync.

Augments manual control with signal output in synchronization with

the start and end of measurement.

START

key: Starts output when measurement starts.

STOP

key: Stops output when measurement stops.

Keys

Augments manual control by allowing signal output to be

manipulated using the instrument’s keys.

START

key: Starts output.

STOP

key: Stops output.

Manual Trigger key: Pauses output.

(For details, see the instruction manual of Models U8793, MR8790, and MR8791.)

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands