Hioki MR8827 Instruction Manual Download Page 150

Page: 150 / 436

145

Add Comments

Enter Text From a Term List or History List

While the virtual keyboard is displayed, pressing the

WAVE

key brings up a “Term List” and

pressing the

AB CSR

key brings up a “History List.”

This can be used to enter preset terms or reuse text from previous input sessions.

Move the cursor to the comment field and select

[Enter Char]

The virtual keyboard will be displayed.

Press the

WAVE

key to select from preset terms.

A list of preset terms will be displayed.

Press the

AB CSR

key to select from the past inputs.

A History list will be displayed.

Press the

ESC

key to cancel selection from the history list.

Use the

Up/down CURSOR

keys or the

jog

knob to select a term from the list, and select

[Enter

Char]

Select [Confirm].

The entry is accepted.

The virtual keyboard will disappear.

Utility Functions

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands