Hioki MR8827 Instruction Manual Download Page 396

Page: 396 / 436

391

Error Messages

Msg

No.

Message

Remedy

References

Channels that are not

measurable will be assigned to

X-Y.

Channel with specification

exceeding

[Used Ch]

is selected.

Change channel selection.

“8.4 Setting Channels to Use

(Extending the Recording

Length)” (p. 150)

There is not enough data in the

memory.

Measure the correct amount data

required for calculation.

“11.1 Waveform Calculation

Workflow” (p. 226)

Stopped.

—

Current clamp/sensor was

recognized.

—

Current clamp/sensor was

disconnected.

Check the connection of the

current clamp/sensor.

—

Channels may no longer be able

to be used by frequency units

due to logic channel use.

If LA to LE or LD to LH are used,

the frequency units cannot be

used at channels CH1 to CH4 or

CH17 to CH20 respectively.

“3.4.3 Logic Channel Settings”

(p. 66)

This module cannot be used

because it is not AAF aligned.

Press the

SYSTEM

key to display

the

[Init]

sheet.

Execute

[System Information]

and check the software items.

[Not AAF aligned]

is displayed,

send the module for repairs.

—

There are module on which AAF

cannot be set to On because of

lack of adjustment.

Roll Mode is not available.

Roll Mode cannot be used when

Overlay is enabled.

“8.2 Display Waveforms During

Recording (Roll Mode)” (p. 147)

Cannot use. (Pre Trigger)

The pre-trigger function is not

available when using external

sampling.

“17 External Control” (p. 335)

Cannot use. (Roll Mode, Memory

Division)

If the waveform calculation

function is in use, these functions

cannot be used.

“11.1 Waveform Calculation

Workflow” (p. 226)

Cannot use. (Roll Mode, Memory

Division, Wave Calculation)

If one function is in use, the other

functions cannot be used.

“8.2 Display Waveforms During

Recording (Roll Mode)” (p. 147)

Cannot use.(Overlay)

The overlay function is not

available when using the Roll

mode.

“8.3 Display New Waveforms

Over Past Waveforms (Overlay)”

(p. 148)

Cannot use. (Overlay, Memory

Division, Wave Calculation)

If roll mode is in use, these

functions cannot be used.

“8.2 Display Waveforms During

Recording (Roll Mode)” (p. 147)

Real-time printing is not available. Recording Length (Shot) is set

to Continuous (

[Cont.] [On]

Real-time printing is not available

when using the Recorder function

and a fast timebase setting.

“3.3.3 Recording Length (Number

of Divisions)” (p. 57)

“6.2 Auto-print Settings” (p. 109)

Maintenance and Service

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands