Hioki MR8827 Instruction Manual Download Page 269

Page: 269 / 436

264

Screen Display Settings

When “Drawing failed” is displayed

•

NG: Nyquist, Running Spectrum

The display format settings and analysis mode do not match.

•

NG:

X-Axis

Either change the

[Format]

setting and increase the number of screen divisions or change the

display setting of the X-axis.

Linear and logarithmic X-axes cannot be displayed on the same graph.

•

NG: X-unit

Set

[Format]

and increase the number of screen divisions. Different horizontal axis units

cannot be displayed on the same graph.

•

NG: EXT

Analysis mode cannot perform external sampling.

Display Types and Split-Screen Settings

Nine display arrangements are available.

Standard

Nyquist

Running

Spectrum

Single standard

Dual standard

Single Nyquist

Dual Nyquist

Running spectrum

[Reference]

setting

[New Data]

[From Memory]

[New Data]

[From Memory]

[New Data]

One division

FFT

MEM

FFT

Nyquist

Running spectrum

Two divisions

FFT

MEM

FFT

Nyquist

MEM

Nyquist

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands