Hioki MR8827 Instruction Manual Download Page 44

Page: 44 / 436

Connection Cables

Output Pulse Waveform

Required items: Commercially available cable

(Half-pitch 50 pins)

Applicable Module

•Model MR8791 Pulse Generator

Unit

To Connect to Output Connector

Output connector

Connect to the object to which

the waveform is being applied.

Required items: Commercially available cable

Connect the connection cable to Output

Connector of module.

Connect the connection cable to the object to

which the waveform is being applied.

To disconnect output connectors

Hold the button of connection cable while pulling the

connector.

Connection cable connector

Button

Output connector

Connect the Connection cable

Output connector

10250-52A2PL: 3M products (SCSI-2 connector), (Centronics half-pitch 50 pin socket-contact)

Refer to: “Output Connector Specifications” (p. 33)

•

Metal shell of the connector 10250-52A2PL is the same as GND of the instrument (frame GND).

•

Use lock type connectors for connecting the harness and the connector.

Measurement Preparation

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands