manualshive.com logo in svg

Hioki MR8827, Instruction Manual

The Hioki MR8827 comes with a comprehensive Instruction Manual that ensures easy integration of this feature-packed product. Users can conveniently download the manual for free from our website, providing step-by-step guidance and a deeper understanding of the MR8827's capabilities. Enhance your experience with this reliable measurement instrument today!

Share
Download
background image

26

Install or Remove Modules

2.1  Install or Remove Modules

Read “Handling the Instrument and Modules” (p. 7) carefully.

Modules specified when the instrument is ordered are supplied preinstalled. Use the following procedures 

to add, replace, or remove modules from the instrument.

 •

Up to two logic units can be installed as units 1 to 8. Logic units installed as the other units 

cannot be used. Other logic units being installed will be disabled.

 •

For information on the analog channel resolution when logic channels are used, refer to “8.10 

Detailed Settings for Modules” (p. 164).

To Install a Module

Back side

Required items: One Phillips-head screwdriver (No. 2)

1 

Turn off the power to the instrument.

2 

Correctly orient the module and insert it firmly all the way in.

Make certain that the labels on the module's panel face the same 

direction as the labels on the back side of the instrument.

3 

Using a Phillips screwdriver, tighten the two module mounting 

screws (M3 × 7.5 mm).

To Remove a Module

Handle

Handle

(Example: 8966)

Back side

Required items: One Phillips-head screwdriver (No. 2)

1 

Turn off the power to the instrument.

2 

Remove any connection cables or thermocouples connected to 

the module.

3 

Remove the power cord.

4 

Using a Phillips screwdriver, loosen the two module mounting 

screws (M3 × 7.5 mm).

5 

Grasp the handles and pull the module out.

If not Installing Another Module After Removal

Back side

Blank 

panel

1 

Install a blank panel.

2 

Using a Phillips screwdriver, tighten the two mounting screws 

(M3 × 7.5 mm).

Measurements made without a blank panel installed may fail to meet 

specifications because of temperature instability within the module.

Summary of Contents for MR8827





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR8827

Garmin GSD20 Sounder Installation Manual preview
GSD20 Sounder
Brand: Garmin Pages: 12
Garmin GC 12 Installation Instructions Manual preview
GC 12
Brand: Garmin Pages: 13
HABYS Agila 2 Instruction Manual preview
Agila 2
Brand: HABYS Pages: 16
Idmed ToFscan Quick Start preview
ToFscan
Brand: Idmed Pages: 2
Latham 309 Installation Manual preview
309
Brand: Latham Pages: 4
SafeWaze LATITUDE Manual preview
LATITUDE
Brand: SafeWaze Pages: 23
Velleman K4401 Illustrated Assembly Manual preview
K4401
Brand: Velleman Pages: 16
Velleman VTTEST11 Manual preview
VTTEST11
Brand: Velleman Pages: 11
Gardco PG-1 User Manual preview
PG-1
Brand: Gardco Pages: 17
H&S 4242 Operator'S Manual preview
4242
Brand: H&S Pages: 42
Aeroflex IFR 4000 Maintenance Manual preview
IFR 4000
Brand: Aeroflex Pages: 211
Life CIRCOLINA G10q T9 Instructions preview
CIRCOLINA G10q T9
Brand: Life Pages: 2
Focusrite Audio Engineering Novation Launchkey Mini User Manual preview
Novation Launchkey Mini
Brand: Focusrite Audio Engineering Pages: 36
Vitax Supaturf Operator'S Manual preview
Supaturf
Brand: Vitax Pages: 12
Zodiac Sheer Descent Installation And Operation Manual preview
Sheer Descent
Brand: Zodiac Pages: 32
Mainpine IQ Express RF6118 Quick Start Manual preview
IQ Express RF6118
Brand: Mainpine Pages: 2
Wacker Neuson RS 800A Operator'S Manual preview
RS 800A
Brand: Wacker Neuson Pages: 42
KERR 815-1655 Instructions For Use Manual preview
815-1655
Brand: KERR Pages: 32

Brands by name

Popular brands

Load more brands