Hioki MR8827 Instruction Manual Download Page 68

Page: 68 / 436

Select Input Channels

3.4.2

Choose Analog Channel Settings

For information about specific settings for Model 8967 Temp Units, 8969 Strain Unit, U8969 Strain Unit,

8970 Freq Unit, 8971 Current Unit, 8972 DC/RMS Unit, MR8990 Digital Voltmeter Unit, and U8974 High

Voltage Unit, refer to “8.10 Detailed Settings for Modules” (p. 164).

Procedure

Press the

DISP

key to open the Waveform screen, and the press the

CH.SET

key to open the channel settings

window (

[Analog]

sheet)

Move the cursor to the channel for which

you want to change the settings.

3. 4. 5.

Select settings with the

keys.

To copy the setting to another channel

Refer to “8.9 Copy Settings to Other Channels (Copy Function)” (p. 163).

1. Waveform

Display Color

Specifies the color in which the waveform of the selected channel is

displayed. You can also select the same color as other channels.

Off

The waveform is not displayed. If the auto-save setting for

[Save

Channel]

[Disp Ch]

, data for this channel will not be saved.

Refer to “Select the channels to save.” (p. 84).

The waveform is displayed. Select the display color with the

keys

[

↑

]

[

↓

]

All On-Off

Switches the waveform display of all channels to all On or all OFF

2. Vertical Axis

(Voltage Axis)

Range

Sets the vertical axis (voltage axis) range for each channel. The value set

here is the voltage of one increment on the vertical axis.

For information on the full-scale value for various modules, refer to the table

in the section “6. Zero Position” (p. 64).

When the Variable function is

[On]

but variable auto-adjustment is

[Off]

, the

size of the waveform on the screen will not change even if the vertical axis

(voltage) range is changed.

When an over-range condition has occurred

Change the vertical axis (voltage axis) range to a lower sensitivity setting.

3. Coupling

Set the input signal coupling method. Normally, DC coupling should be

selected.

DC (V)

Both DC components and AC components of the input signal will be

measured. (

Default setting)

AC (

)

Only AC components of the input signal will be measured. DC

components will be blocked.

GND ( )

Input is shorted to ground. (Allows checking the zero position.)

Measurement

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands