Hioki MR8827 Instruction Manual Download Page 69

Page: 69 / 436

Select Input Channels

4. Vertical Axis

(Voltage Axis)

Zoom

Vertical axis (voltage axis) zoom-up or zoom-down settings can be selected

separately for each channel. These settings will be used for display and printout.

Zoom is based on the zero position. The measurement resolution does not change.

Refer to “7.5.3 Vertical Axis (Voltage Axis) Magnification” (p. 132).

Use the Variable function for user-specified zoom.

The waveform can be inverted by reversing plus/minus.

Refer to “8.6 Set the Waveform Position (Variable Function)” (p. 158).

Refer to “8.8 Invert the Waveform (Invert Function)” (p. 162).

5. Vernier

Fine adjustment of input voltage can be performed arbitrarily on the

Waveform screen (display only).

When recording physical values such as noise, temperature and acceleration

using sensors, amplitude can be adjusted to facilitate calibration.

Refer to “8.7 Fine Adjustment of Input Values (Vernier Function)” (p. 161).

6. Zero Position

Sets the 0 V level display position. If the 0 V input level has shifted, perform

zero-adjust.

Refer to “2.7 Adjust the Zero Position (Zero-Adjust)” (p. 47).

Refer to “2.8 Perform Calibration (When Model MR8990 is installed)” (p. 48).

The zero position of all channels can be changed at the same time using the

zero position preset (press

[Preset]

Ascending

(3%→96%)

The zero position of CH1 is set to 3% and the following channels

up to CH32 are increased by 3% each.

Descending

(96%→3%)

The zero position of CH1 is set to 96% and the following channels

up to CH32 are decreased by 3% each.

All Ch 0%

The zero position of all channels is set to 0%.

All Ch 50%

The zero position of all channels is set to 50%.

If the zero position of the waveform obtained with Model 8969 or U8969

Strain Unit is displaced, perform the auto-balance.

Refer to “8.10.4 Setting Model 8969 and U8969 Strain Unit” (p. 168).

• Only the display position is shifted. No offset is applied to the input.

• Vertical axis (voltage axis) zooming is based on the zero position.

• Zero position adjustment and vertical axis (voltage axis) zooming only change the voltage range as

displayed on the Waveform screen. The actual measurement range does not change.

The zero position is as shown in the illustration below. (Example: 8966 Analog Unit)

A/D Data

2047

A/D Data

0 V

2000 LSB

100 %

Display screen

(Zero position: 0%)

Display screen

(Zero position: 50%)

Display screen

(Zero position: 100%)

50 %

0 %

−2047

Zoom factor ×1

Full-scale resolution for modules at various vertical axis zoom factors (LSB)

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Brands by name

Popular brands