Hioki MR8827 Instruction Manual Download Page 166

Page: 166 / 436

161

Fine Adjustment of Input Values (Vernier Function)

8.7 Fine Adjustment of Input Values (Vernier

Function)

Fine adjustment of input voltage can be performed arbitrarily on the Waveform screen. When recording

physical values such as noise, temperature and acceleration using sensors, amplitude can be adjusted to

facilitate calibration.

Normal display

Vernier Function Enabled

1.2 V input is displayed as 1.0 V

1.0 V

1.2 V

Procedure

Press the

DISP

key

to open the Waveform screen, and then press the

CH.SET

key

to open the channel settings

window (

[Analog]

sheet).

Move the cursor to the [ ] vernier setting of the channel you
want to adjust.

Make the adjustment with the

keys while watching the

waveform.

Vernier↑

Magnify waveform

Vernier↓

Compress waveform

Vernier Reset

Return waveform to original position

•

The adjustment range is 50 to 200% of the original waveform. The magnification/compression ratio is

not displayed.

•

Vernier adjustments cannot be verified on printed waveforms or lists.

•

The waveform data (print data, saved file data) is adjusted by the Vernier function.

Utility Functions

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands