Hioki MR8827 Instruction Manual Download Page 53

Page: 53 / 436

Perform Calibration (When Model MR8990 is installed)

2.8 Perform Calibration (When Model MR8990 is

installed)

This procedure compensates for MR8990 Digital Voltmeter Unit differences.

The compensation procedure is performed for all channels and ranges.

Before Performing Calibration

•

Before performing this procedure, allow the equipment to warm up for about 30 minutes after the power

is turned on so the internal temperature of the modules can stabilize.

•

Note that calibration cannot be performed during measurement. However, if the calibration setting is set

to ON, calibration is performed at the start of measurement.

•

Key operations are not accepted during calibration.

•

The time required for calibration varies depending on the type and number of modules installed in the

instrument. (The procedure may take several seconds.)

Procedure

Press the

CHAN

key to open the Channel screen, and then select the

[Unit List]

sheet.

Move the cursor to

[Zero-Adjust]

Select

[Exec Zero-Adjust]

Calibration will be performed.

In the following cases, calibration should be executed again.

•

When a module was changed.

•

When power was turned off and on again.

•

When settings were initialized (system reset).

•

When the ambient temperature has changed significantly.

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands