Hioki MR8827 Instruction Manual Download Page 279

Page: 279 / 436

274

FFT Analysis Modes

Nyquist display

• If the cursor is displayed, the total harmonic distortion (THD) with the fundamental wave set to the

cursor position will be displayed. When 2 cursors appear, the A cursor becomes the fundamental

wave. When results cannot be obtained,

[---%]

is displayed.

• When only sine waves are input, the level of this component becomes approximately 1.4 times (3 dB)

larger than the overall value. To measure at a reference the same as the overall value, analyze using

RMS spectrum or power spectrum.

Refer to “RMS Spectrum” (p. 274) or “Power Spectrum” (p. 275).

RMS Spectrum

The oscillation component (actual value) is calculated from the frequency axis waveform of the

input signal.

RMS and power spectra displays use the same analysis results displayed logarithmically

(amplitude in dB).

Main uses:

• To inspect the execution value of the frequency component of the waveform

• To inspect the RMS value of each frequency

About the Functions, refer to “13.9.2 Analysis Mode Functions” (p. 289).

Axis

Display type

Description

X axis

Linear

Displays the frequency on a linear scale

Log

Displays the frequency on a logarithm scale

Y axis

Lin-Mag

Displays analysis values linearly.

Log-Mag

Display analysis results as dB values. (0 dB reference value: 1eu)*

Lin-Real

Display the real-number component of analysis values.

Lin-Imag

Display the imaginary component of analysis values.

* eu: engineering units that are currently set are the standard (e.g., when the unit settings is volts, 0 dB = 1 V)

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Hioki MR8827, Instruction Manual, Page: 279 / 436

Search results

Summary of Contents for MR8827

Reviews: