manualshive.com logo in svg

Hioki MR8827, Instruction Manual

The Hioki MR8827 comes with a comprehensive Instruction Manual that ensures easy integration of this feature-packed product. Users can conveniently download the manual for free from our website, providing step-by-step guidance and a deeper understanding of the MR8827's capabilities. Enhance your experience with this reliable measurement instrument today!

Share
Download
background image

278

FFT Analysis Modes

Transfer Function

From the input and output signals, the transfer function (frequency characteristic) of a 

measurement system can be obtained. It can also be displayed as a Nyquist plot.

Main uses:

 •

To inspect a filter’s frequency characteristic

 • To inspect the stability of a feedback control system (using the Nyquist plot)

 • To inspect the resonance characteristic of an object using an impulse hammer and pick-up sensor

 About the Functions, refer to“13.9.2 Analysis Mode Functions” (p. 289) or Refer to “Linear Time-Invariant Systems” 

(p. A14).

Axis

Display type

Description

X axis

Linear

Displays the frequency on a linear scale

Log

Displays the frequency on a logarithm scale

Nyquist display

Displays the real-number component of the input-output ratio.

Y axis

Lin-Mag

Displays the input-output ratio linearly (dimensionless units).  

Log-Mag(logarithm) Displays the input-output ratio as dB values.
Lin-Real

Displays the real-number component of the input-output ratio. (dimensionless 

units)

Lin-Imag

Displays the imaginary component of the input-output ratio. (dimensionless 

units)

Nyquist display

Displays the imaginary component of the input-output ratio.

Waveform Example

Normal display

X axis: Log

Y axis: Lin-Mag

Normal display

X axis: Log

Y axis: Log-Mag

Normal display

X axis: Log

Y axis: Lin-Real

Normal display

X axis: Log

Y axis: Lin-Imag

Nyquist display

Summary of Contents for MR8827





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR8827

UFO Vega Product User Manual preview
Vega
Brand: UFO Pages: 16
Eazyzap Y724 Instruction Manual preview
Y724
Brand: Eazyzap Pages: 32
Obdstar MS50 User Manual preview
MS50
Brand: Obdstar Pages: 42
GE PANDA Service Manual preview
PANDA
Brand: GE Pages: 212
Jackson DISHSTAR ADA-SEER Operation Manual preview
DISHSTAR ADA-SEER
Brand: Jackson Pages: 2
Maeda MC-174CRM Operation Manual preview
MC-174CRM
Brand: Maeda Pages: 276
MacDon FlexDraper FD2 Series Quick Start Manual preview
FlexDraper FD2 Series
Brand: MacDon Pages: 2
M-Audio OXYGEN PRO MINI Quick Start Manual preview
OXYGEN PRO MINI
Brand: M-Audio Pages: 56
Magma ONIX Operation And Maintenance Manual preview
ONIX
Brand: Magma Pages: 16
MAHA MBT Series Operating Instructions Manual preview
MBT Series
Brand: MAHA Pages: 21
MAGUIRE PRS-20 Installation Operation & Maintenance preview
PRS-20
Brand: MAGUIRE Pages: 47
TAKAYA APT-9411 Series Service Manual preview
APT-9411 Series
Brand: TAKAYA Pages: 77
Tadano TR-800XXL4 Service Manual preview
TR-800XXL4
Brand: Tadano Pages: 402
U-Line S-11303 Quick Start Manual preview
S-11303
Brand: U-Line Pages: 3
U-Line H-3736 Installation Instructions preview
H-3736
Brand: U-Line Pages: 2
ebm-papst R1G225-AG15-11 Operating Instructions Manual preview
R1G225-AG15-11
Brand: ebm-papst Pages: 10
Eaton CEAG Exit Cube 33822 LED CGLine+ Mounting And Operating Instructions preview
CEAG Exit Cube 33822 LED CGLine+
Brand: Eaton Pages: 20
swamp LT-LP-F09 User Manual preview
LT-LP-F09
Brand: swamp Pages: 5

Brands by name

Popular brands

Load more brands