Hioki MR8827 Instruction Manual Download Page 56

Page: 56 / 436

Pre-measurement Inspection

3.2 Pre-measurement Inspection

Verify that the instrument operates normally to ensure that no damage occurred during storage or

shipping. If you find any damage, contact your authorized Hioki distributor or reseller.

(1)

Peripheral Device Inspection

Is the insulation of the probe or connection

cable to be used damaged, or is bare metal

exposed?

Is the clamp cracked or damaged?

Do not use if damage is present, as

you could receive an electric shock.

Request repairs.

When using probes and connection cables

When using a clamp sensor

Metal Exposed

Yes

No Metal Exposed

Go to Step (2)

(2) Instrument and Module Inspection

Is there any visible damage to the instrument

or modules?

Do the fans turn and the Hioki logo appear on

the screen?

Does the Waveform screen appear?

If damage is evident, request repairs.

The power cord may be damaged,

or the instrument may be damaged

internally. Request repairs.

The instrument may be damaged

internally. Request repairs.

Yes

Nothing appears,

or the display is

abnormal

Yes

When turning power on

Inspection complete

Measurement

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands