Hioki MR8827 Instruction Manual Download Page 77

Page: 77 / 436

Measurement Workflow

4.1

Measurement Workflow

1 Pre-measurement Inspection

Refer to “3.2 Pre-measurement Inspection” (p. 51).

2 Basic Measurement Settings

Refer to...

Select X-Y recorder as measurement function

“Function” (p. 73)

Set sampling rate

“Sampling” (p. 73)

Determine screen layout format

“Format” (p. 73)

Determine whether to perform waveform

interpolation

“Setting Descriptions” (p. 73)

Determine whether to clear previous

waveform data

“Disp Clear” (p. 73)

3 Input Channel Settings

Choose analog channel settings

Refer to “3.4.2 Choose Analog Channel

Settings” (p. 63).

Logic channels cannot be used.

Application examples

Refer to...

“8.6 Set the Waveform Position (Variable Function)” (p. 158)

“8.7 Fine Adjustment of Input Values (Vernier Function)” (p. 161)

“8.1 Add Comments” (p. 140)

“8.5 Convert Input Values (Scaling Function)” (p. 151)

4 Start Measurement

Refer to...

“4.3 Start and Stop Measurement” (p. 74)

“7.1 Read Measurement Values (Using the AB Cursors)”

(p. 122)

With the X-Y recorder function, the

following operations are not available:

•Trigger setting

•Auto-saving

•Auto-printing

5 Stop Measurement

Refer to...

“4.3 Start and Stop Measurement” (p. 74)

“4 Redraw waveforms” (p. 74)

“5.2.3 Save Data Selectively (SAVE Key)” (p. 88)

“6.3 Manual Printing With the PRINT Key (Selective Printing)” (p. 112)

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands