Hioki MR8827 Instruction Manual Download Page 145

Page: 145 / 436

140

Add Comments

8.1 Add Comments

8.1.1

Add a Title Comment

When you enter a title comment, it can be displayed at the top of the Waveform screen, and can also be

printed.

(Allowed number of characters: up to 40)

Refer to “6.6.2 Report Print (A4 Size Print)” (p. 118).

Procedure

Press the

CHAN

key

to open the Channel screen, and then select the

[Comment]

sheet.

Set the print title content

Move the cursor to

[Title Print]

for the title.

Off

Title comment not printed.

Setting

Equipment settings will be printed.

Comment Title will be printed.
Set&

Com

Both equipment settings and title will be

printed.

Enter a title comment.

Move the cursor to

[Comment].

Input

Enter comment text.

Refer to “Entering Text” (p. 143).

Clear

Clear entered information

Undo

Return to the state before the most recent

change

To select from preset terms

Pressing the

WAVE

key after activating text input brings up a list of preset terms.

It is also possible to select words from previously entered titles (History function).

Refer to “Enter Text From a Term List or History List” (p. 145).

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Hioki MR8827, Instruction Manual, Page: 145 / 436

Search results

Summary of Contents for MR8827

Reviews: