Hioki MR8827 Instruction Manual Download Page 82

Page: 82 / 436

Save/Load Data and Manage

Files

This chapter explains how to

save and load data and manage files on your Hioki Memory HiCorder.

Before saving data, configure the save settings on the

[File Save]

sheet.

You can load data and manage files from the

File screen

To Open the

[File Save]

Sheet

Press this key repeatedly to

display the various sheets.

[Environment] [Init]

[File Save]

[Printer]

[Interface]

Operations available from the [File Save] sheet

The following settings are available on the

[File Save]

sheet. (p. 81)

Auto-save settings

Set the method of automatic saving of waveform data.

SAVE

key settings

Set the method of saving when the

SAVE

key is pressed.

Save/Load Data and Manage Files

Summary of Contents for MR8827




















































































































































































































































































































































































































































Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands

Hioki MR8827, Instruction Manual

Search results

Summary of Contents for MR8827

Reviews:

Related manuals for MR8827

Brands by name

Popular brands