Bosch Rexroth IndraDrive MPB-02 Скачать руководство пользователя страница 340 | Manualshive

Страница: 340 / 728

background image

7-34

Operating Modes

MPH-02, MPB-02, MPD-02

DOK-INDRV*-MP*-02VRS**-FK01-EN-P

Via bit 5 of S-0-0346 it is possible to determine the time of the reaction to
a new target position preset:

•

bit 5= 0:

The drive travels to the last preset target before positioning at the new
target. The target is considered to have been reached when the
following applies:
target position – actual position value < positioning window

•

bit 5 =1:

The previous target is rejected and the drive immediately travels to the
new target.

→

immediate block change

See also Parameter Description "S-0-0346, Positioning control

word"

The

S-0-0393, Command value mode

parameter controls the drive

behavior in the case of

position processing in modulo format

. For

S-0-0393 the following definition applies:

•

bit 1/0 = 00: positive direction of rotation

•

bit 1/0 = 01: negative direction of rotation

•

bit 1/0 = 10: shortest distance

See also Parameter Description "S-0-0393, Command value

mode"

The following special cases apply for evaluating the settings for

S-0-0393,

Command value mode

:

•

If the absolute value of the current actual velocity is greater than the

velocity threshold for positioning (

S-0-0417, Velocity threshold for

positioning in modulo format

), the drive always moves in the last

active direction of rotation.

•

If the target position is within the target position window (S-0-0418),

positioning is always carried out according to the "shortest distance"
mode.

Note:

If the velocity threshold for positioning behavior was
parameterized with very low values that are within the noise
level of the actual velocity value, this can cause unpredictable
behavior.

See also Parameter Description "S-0-0417, Velocity threshold for

positioning in modulo format" and "S-0-0418, Target position window in
modulo format" and "S-0-0430, Effective target position"

Positioning Generator

The drive generates the position command value profile necessary to
move to the target position, considering the conditions defined in the
following parameters:

•

S-0-0108, Feedrate override

•

S-0-0193, Positioning Jerk

•

S-0-0259, Positioning Velocity

•

S-0-0260, Positioning Acceleration

•

S-0-0359, Positioning Deceleration

Reaction to New Target Position

Preset

Processing in Modulo Format

Special Cases

Courtesy

of

CMA/Flodyne/Hydradyne

▪

Motion

Control

▪

Hydraulic

▪

Pneumatic

▪

Electrical

▪

Mechanical

▪

(800)

426-5480

▪

www.cmafh.com

«
...
338
339
340
341
342
...
»

Содержание Rexroth IndraDrive MPB-02

























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth IndraDrive MPB-02

Бренд: ABB Страницы: 2

Бренд: FrSky Страницы: 2

Бренд: QUAD Страницы: 17

Бренд: fadini Страницы: 16

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 11

Бренд: Nauticam Страницы: 2

Бренд: National Instruments Страницы: 18

Бренд: National Instruments Страницы: 10

Бренд: National Instruments Страницы: 20

GEMINI C Series

Бренд: NAPCO Страницы: 24

Бренд: Panamax Страницы: 16

Бренд: Rain Bird Страницы: 20

Бренд: K&G GROEP Страницы: 27

Бренд: CAME Страницы: 2

Бренд: CalAmp Страницы: 13

AMES 4000SS Series

Бренд: Watts Страницы: 8

Бренд: NXP Semiconductors Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды