Bosch Rexroth IndraDrive MPB-02 Скачать руководство пользователя страница 241 | Manualshive

Страница: 241 / 728

background image

MPH-02, MPB-02, MPD-02

Drive Control

6-29

DOK-INDRV*-MP*-02VRS**-FK01-EN-P

4. After the current was supplied and the commutation offset value has

been successfully determined this value is contained in

P-0-0521,

Effective commutation offset

. The drive now is operational. In

addition, the motor-specific values for P-0-0506 and P-0-0507 were
stored.

Note:

The motor-specific values for P-0-0506 and P-0-0507 should
be checked for their safe function, independent of the position.
To do this, set axis to several different positions within one
pole pair or pole pair distance, execute command C1200 each
time and write down value of P-0-0521. If P-0-0521 shows
great deviations (>

approx.

+/-30) or error messages are

generated, the values of P-0-0506 and P-0-0507 have to be
automatically generated again (see above) or subsequently
manually optimized.

−

With error message "F8013" (current too low):

→

increase voltage (P-0-0506), reduce frequency

(P-0-0507)

−

With error message "F8014" (overcurrent):

→

reduce voltage (P-0-0506), increase frequency

(P-0-0507)

If error message "F8013" occurs, but the deviation of P-0-0521
is within the allowed range of values (< approx. +/-30), further
measures can be taken as described for F8013 in the
Troubleshooting Guide!

Note:

It is recommended to execute the command C1200 several
times over a pole pair or a distance between pole centers, to
generate and enter the average value of P-0-0521. Checking
and optimizing P-0-0521 by force or torque measurement at
the axis is recommended!

See also below "Manually Optimizing Commut. Offset Value"

5. Now switch drive to parameter mode (P2). After switching back to

operating mode, set "AF" and test function of drive. This automatically
start the determination of the commutation offset with the stored
parameters (P-0-0506, P-0-0507, P-0-0517). The motor is supplied
with current and the commutation offset determined again.

Test commutation behavior of the drive at several different positions.
If it is not satisfactory, repeat manual optimization of P-0-0506,
P-0-0507, P-0-0517 as described below.

Note:

If inadmissible values are generated for

P-0-0521, Effective

commutation offset

and therefore the message

F8078

Speed loop error

appears although there wasn’t any error

signaled during commutation determination, the value of
parameter

P-0-0517, Commutation: required harmonics

component

has to be increased!

6. Now start

S-0-0148, C0600 Drive-controlled homing procedure

command

. By this command, due to the active initial commissioning

mode, the value of P-0-0521 referring to an arbitrary position is
converted to the position of the home point and stored in

P-0-0508,

Commutation offset

and

P-0-3008, Commutation offset, encoder

memory

(if available).

Courtesy

of

CMA/Flodyne/Hydradyne

▪

Motion

Control

▪

Hydraulic

▪

Pneumatic

▪

Electrical

▪

Mechanical

▪

(800)

426-5480

▪

www.cmafh.com

«
...
239
240
241
242
243
...
»

Содержание Rexroth IndraDrive MPB-02

























































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth IndraDrive MPB-02

Бренд: Unipulse Страницы: 99

Бренд: Accutrol Страницы: 25

Бренд: Mainpine Страницы: 16

Бренд: Danfoss Страницы: 20

Бренд: Watts Страницы: 2

Бренд: Hanbay Страницы: 18

Бренд: BabySafe Страницы: 24

Бренд: VAT Страницы: 27

MorphoAccess SIGMA Extreme Series

Бренд: Idemia Страницы: 31

Бренд: ICP DAS USA Страницы: 148

Бренд: ICMA Страницы: 8

Бренд: MacDon Страницы: 32

Бренд: K&K Страницы: 6

Бренд: Madas Страницы: 6

Бренд: Madas Страницы: 11

Бренд: R82 Страницы: 89

Бренд: NCR Страницы: 8

Total Access 351 Series

Бренд: ADTRAN Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды