Mitsubishi Electric Melservo MR-J3-100B, Handbook

Page: 77 / 590

Part 2: Review on Replacement of MR-J3-_A_ with MR-J4-_A_
2 - 44
MR-J3-_A_ MR-J4-_A_
Control
mode
No.
Name and function
Initial
value
No.
Name and function
Initial
value
PC14 Analog monitor 1 output
Used to selection the signal provided to the analog
monitor 1 (MO1) output.
0 0 0 x:
Analog monitor 1 (MO1) output selection
Setting Item
0 Servo motor speed (8 V/max. speed)
1 Torque (8 V/max. torque) (Note 2)
2 Servo motor speed (+8 V/max. speed)
3 Torque (+8 V/max. torque) (Note 2)
4 Current command (8 V/max. current command
5 Command pulse frequency (10 V/1Mpps)
6 Droop pulses (10 V/100 pulses) (Note 1)
7 Droop pulses (10 V/1000 pulses) (Note 1)
8 Droop pulses (10 V/10000 pulses) (Note 1)
9 Droop pulses (10 V/100000 pulses) (Note 1)
A Feedback position (10 V/1 Mpulses) (Note 1)
B Feedback position (10 V/10 Mpulses) (Note 1)
C Feedback position (10 V/100 Mpulses) (Note 1)
D Bus voltage (8 V/400 V) (Note 3)
0000h PC14 Analog monitor 1 output
_ _ x x:
Analog monitor 1 output selection
Select a signal to output to MO1 (Analog monitor 1).
Refer to table 2.6 for settings.
00h P
S
T
_ x _ _:
For manufacturer setting 0h
x _ _ _:
For manufacturer setting 0h
Table 2.6 Analog monitor setting value
(MR-J4-_A_(-RJ) 100 W or more)
Setting
value
Item
Operatio
n mode
(Note 1)
Standard
_ _ 0 0 (Linear) servo motor speed (±8 V/max. speed)
_ _ 0 1 Torque or thrust (±8 V/max. torque or max. thrust)
(Note 3)
_ _ 0 2 (Linear) servo motor speed (+8 V/max. speed)
_ _ 0 3 Torque or thrust (+8 V/max. torque or max. thrust)
(Note 3)
_ _ 0 4 Current command (±8 V/max. current command)
_ _ 0 5 Command pulse frequency (±10 V/±4 Mpulses/s)
_ _ 0 6 Servo motor-side droop pulses (±10 V/100 pulses)
(Note 2)
_ _ 0 7 Servo motor-side droop pulses (±10 V/1000 pulses)
(Note 2)
_ _ 0 8 Servo motor-side droop pulses (±10 V/10000 pulses)
(Note 2)
_ _ 0 9 Servo motor-side droop pulses (±10 V/100000 pulses)
(Note 2)
_ _ 0 A Feedback position (±10 V/1 Mpulse) (Note 2)
_ _ 0 B Feedback position (±10 V/10 Mpulses) (Note 2)
_ _ 0 C Feedback position (±10 V/100 Mpulses) (Note 2)
_ _ 0 D Bus voltage (200 V class and 100 V class: +8 V/400 V,
400 V class: +8 V/800 V)
_ _ 0 E Speed command 2 (±8 V/max. speed)
_ _ 1 0 Load-side droop pulses (±10 V/100 pulses) (Note 2)
_ _ 1 1 Load-side droop pulses (±10 V/1000 pulses) (Note 2)
_ _ 1 2 Load-side droop pulses (±10 V/10000 pulses) (Note 2)
_ _ 1 3 Load-side droop pulses (±10 V/100000 pulses) (Note 2)
_ _ 1 4 Load-side droop pulses (±10 V/1 Mpulse) (Note 2)
_ _ 1 5 Servo motor-side/load-side position deviation
(±10 V/100000 pulses)
_ _ 1 6 Servo motor-side/load-side speed deviation
(±8 V/max. speed)
_ _ 1 7 Internal temperature of encoder (±10 V/±128 °C)
Note 1. Encoder pulse unit.
2. 8 V is outputted at the maximum torque.
However, when [Pr. PA11] [Pr. PA12] are
set to limit torque, 8 V is outputted at the
torque highly limited.
3. For 400 V class servo amplifier, the bus
voltage b8 V/800 V.
Note 1.
2.
3.
Items with

are available for each
operation mode.
Standard: Standard (semi closed loop
system) use of the rotary servo
motor
Encoder pulse unit
The larger value of [Pr. PA11] or [Pr. PA12]
will be the maximum torque.
PC15 Analog monitor 2 output
Used to selection the signal provided to the analog
monitor 2 (MO2) output.
0 0 0 x:
Select the analog monitor 2 (MO2) output
The settings are the same as those of [Pr. PC14]
0001h PC15 Analog monitor 2 output
Analog monitor 2 output selection
_ _ x x:
Select a signal to output to MO2 (Analog monitor 2).
Refer to [Pr. PC14] for settings.
01h P
S
T
_ x _ _:
For manufacturer setting
0h
x _ _ _:
For manufacturer setting
0h
PC16 Electromagnetic brake sequence output
Used to set the delay time (Tb) between electronic
brake interlock (MBR) and the base drive circuit is
shut-off.
100 PC16 Same as MR-J3 0 P
S
T
Analog monitor 2 output
Set the delay time between MBR (Electromagnetic
brake interlock) and the base drive circuit is shut-off.
Setting range: 0 to 1000