Mitsubishi Electric Melservo MR-J3-100B, Handbook

Page: 180 / 590

Part 4: Replacement of MR-J3W-_B with MR-J4W2-_B
4 - 35
MR-J3W-_B MR-J4W2-_B
No. Name and function
Initial
value
No. Name and function
Initial
value
PB19 Vibration suppression control vibration frequency setting
This parameter cannot be used in the speed control
mode.
Set the vibration frequency for vibration suppression
control to suppress low-frequency machine vibration,
such as enclosure vibration.
When [Pr. PB02] is set to "_ _ _ 2" , this parameter can
be set manually.
100.0 PB19 Vibration suppression control 1 - Vibration frequency
Set the vibration frequency for vibration suppression
control 1 to suppress low-frequency machine vibration.
When "Vibration suppression control 1 tuning mode
selection" is set to "Automatic setting (_ _ _ 1)" in [Pr.
PB02], this parameter will be set automatically. When
"Manual setting (_ _ _ 2)" is selected, the setting written
to the parameter is used.
The setting range of this parameter varies, depending on
the value in [Pr. PB07]. If a value out of the range is set,
the vibration suppression control will be disabled.
100.0
PB20 Vibration suppression control resonance frequency
setting
This parameter cannot be used in the speed control
mode.
Set the resonance frequency for vibration suppression
control to suppress low-frequency machine vibration,
such as enclosure vibration.
When [Pr. PB02] is set to "_ _ _ 2" , this parameter can
be set manually. 100.0 PB20 Vibration suppression control 1 - Resonance frequency
Set the resonance frequency for vibration suppression
control 1 to suppress low-frequency machine vibration.
When "Vibration suppression control 1 tuning mode
selection" is set to "Automatic setting (_ _ _ 1)" in [Pr.
PB02], this parameter will be set automatically. When
"Manual setting (_ _ _ 2)" is selected, the setting written
to the parameter is used.
The setting range of this parameter varies, depending on
the value in [Pr. PB07]. If a value out of the range is set,
the vibration suppression control will be disabled. 100.0
PB21 This parameter is not used. Do not change the value. 0.00 PB21 Vibration suppression control 1 - Vibration frequency
damping
Set a damping of the vibration frequency for vibration
suppression control 1 to suppress low-frequency
machine vibration.
When "Vibration suppression control 1 tuning mode
selection" is set to "Automatic setting (_ _ _ 1)" in [Pr.
PB02], this parameter will be set automatically. When
"Manual setting (_ _ _ 2)" is selected, the setting written
to the parameter is used.
0.00
PB22 This parameter is not used. Do not change the value. 0.00 PB22 Vibration suppression control 1 - Resonance frequency
damping
Set a damping of the resonance frequency for vibration
suppression control 1 to suppress low-frequency
machine vibration.
When "Vibration suppression control 1 tuning mode
selection" is set to "Automatic setting (_ _ _ 1)" in [Pr.
PB02], this parameter will be set automatically. When
"Manual setting (_ _ _ 2)" is selected, the setting written
to the parameter is used.
0.00
PB23 Low-pass filter selection
Select the low-pass filter.
0 0 x 0:
Low-pass filter selection
0: Automatic setting
1: Manual setting ([Pr. PB18] setting)
When automatic setting has been selected, select the
filter that has the band width close to the one calculated
with
GD2 + 1
10 VG2 ・
[rad/s]
0000h PB23 Low-pass filter selection
Select the shaft resonance suppression filter and low-
pass filter.
_ _ _ x:
Shaft resonance suppression filter selection
0: Automatic setting
1: Manual setting
2: Disabled
When you select "Enabled (_ _ _ 1)" of "Machine
resonance suppression filter 4 selection" in [Pr. PB49],
the shaft resonance suppression filter is not available. 0h
_ _ x _ :
Low-pass filter selection
0: Automatic setting
1: Manual setting
2: Disabled 0h
_ x _ _ :
For manufacturer setting 0h
x _ _ _ :
For manufacturer setting 0h