Atmel SAM4S Series Preliminary Data Sheet Download

Page: 966 / 1163

966

11100B–ATARM–31-Jul-12

SAM4S Series [Preliminary]

37.7.32

PWM Comparison x Value Register

Name:

PWM_CMPVx

Address:

0x40020130 [0], 0x40020140 [1], 0x40020150 [2], 0x40020160 [3], 0x40020170 [4], 0x40020180 [5],

0x40020190 [6], 0x400201A0 [7]

Access:

Read-write

Only the first 16 bits (channel counter size) of field CV are significant.

• CV: Comparison x Value

Define the comparison x value to be compared with the counter of the channel 0.

• CVM: Comparison x Value Mode

0 = The comparison x between the counter of the channel 0 and the comparison x value is performed when this counter is
incrementing.

1 = The comparison x between the counter of the channel 0 and the comparison x value is performed when this counter is
decrementing.

Note:

This bit is useless if the counter of the channel 0 is left aligned (CALG = 0 in

“PWM Channel Mode Register” on page 970

)

–

CVM

Summary of Contents for SAM4S Series












































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SAM4S Series

Reviews:

Related manuals for SAM4S Series

Brands by name

Popular brands

Atmel SAM4S Series, Preliminary Data Sheet

Search results

Summary of Contents for SAM4S Series

Reviews:

Related manuals for SAM4S Series

Brands by name

Popular brands