manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 2009 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 2009

OmniSwitch 6250 CLI Reference Guide

November 2009

page 15

QoS Policy Commands

policy condition 

condition_name

 icmptype 

type

policy condition 

condition_name

 no icmptype

policy condition 

condition_name

 icmpcode 

code

policy condition 

condition_name

 no icmpcode

policy condition 

condition_name

 ip protocol 

protocol

policy condition 

condition_name

 no ip protocol

policy condition 

condition_name

 ipv6

policy condition 

condition_name

 no ipv6

policy condition 

condition_name

 tos 

tos_value 

[mask 

tos_mask

]

policy condition 

conditioning

 no tos

policy condition 

condition_name

 dscp {

dscp_value

[

-value

]}

policy condition 

condition_name

 no dscp

policy condition 

condition_name

 source mac 

mac_address

 [mask 

mac_mask

]

policy condition 

condition_name

 no source mac

policy condition 

condition_name

 destination mac 

mac_address

 [mask 

mac_mask

]

policy condition 

condition_name

 no destination mac

policy condition 

condition_name

 source mac group 

group_name

policy condition 

condition_name

 no source mac group

policy condition 

condition_name

 destination mac group 

mac_group

policy condition 

condition_name

 no destination

policy condition 

condition_name

 source vlan 

vlan_id

policy condition 

condition_name

 no source vlan

policy condition 

condition_name

 destination vlan 

vlan_id

policy condition 

condition_name

 no destination vlan

policy condition 

condition_name

 802.1p 

802.1p_value

policy condition 

condition_name

 no 802.1p

policy condition 

condition_name

 source port 

slot/port

[-

port

]

policy condition 

condition_name

 no source port

policy condition 

condition_name

 destination port 

slot/port

[-

port

]

policy condition 

condition_name

 no destination port

policy condition 

condition_name

 source port group 

group_name

policy condition 

condition_name

 no source port group

policy condition 

condition_name

 destination port group 

group_name

policy condition 

condition_name

 no destination port

policy action 

action_name

policy no action 

action_name

policy action 

action_name

 disposition {accept | drop | deny}

policy action 

action_name

 no disposition

policy action 

action_name

 shared

policy action 

action_name

 no shared

policy action 

action_name

 priority 

priority_value

policy action 

action_name

 no priority

policy action 

action_name

 maximum bandwidth 

bps

policy action 

action_name

 no maximum bandwidth

policy action 

action_name

 maximum depth 

bytes

policy action 

action_name

 no maximum depth

policy action 

action_name

 tos 

tos_value

policy action 

action_name

 no tos

policy action 

action_name

 802.1p 

802.1p_value

policy action 

action_name

 no 802.1p

policy action 

action_name

 dscp 

dscp_value

policy action 

action_name

 no dscp

policy action map {802.1p | tos | dscp} to {802.1p | tos| dscp} using 

map_group

policy action no map
policy action 

action_name

 permanent gateway ip 

ip_address

policy action 

action_name

 no permanent gateway ip

policy action 

action_name

 port-disable

policy action 

action_name

 no port-disable

policy action 

action_name

 redirect port 

slot/port

policy action 

action_name

 no redirect port

policy action 

action_name

 redirect linkagg 

link_agg

policy action 

action_name

 no redirect linkagg

policy action 

action_name

 no-cache

policy action 

action_name

 no no-cache

policy action 

action_name

 ingress mirror 

slot/port

policy action 

action_name

 no mirror 

slot/port

policy action action_name cir bps [cbs 

byte

] [pir bps] [pbs 

byte

]

policy action action_name no cir bps
show policy classify {l2 | l3 | multicast} [applied]
show policy classify {l2 | l3 | multicast} [applied] source port 

slot/port

show policy classify {l2 | l3 | multicast} [applied] source mac 

mac_address

show policy classify {l2 | l3 multicast} [applied] destination mac 

mac_address

show policy classify {l2 | l3 | multicast} [applied] source vlan 

vlan_id

show policy classify {l2 | l3 | multicast} [applied] destination vlan 

vlan_id

show policy classify {l2 | l3 | multicast} [applied] source interface type {ethernet | wan | 

ethernet-10 | ethernet-100 | ethernet-1G | ethernet-10G}

show policy classify {l2 | l3 | multicast} [applied] source ip 

ip_address

show policy classify {l2 | l3 | multicast} [applied] destination ip 

ip_address

show policy classify {l2 | l3 | multicast} [applied] multicast ip 

ip_address

show policy classify {l2 | l3 | multicast} [applied] tos 

tos_value

show policy classify {l2 | l3 | multicast} [applied] dscp 

dscp_value

show policy classify {l2 | l3 | multicast} [applied] ip protocol 

protocol

show policy classify {l2 | l3 | multicast} [applied] source ip port 

port

show policy classify {l2 | l3 | multicast} [applied] destination ip port 

port

show [applied] policy network group [

network_group

]

show [applied] policy service [

service_name

]

show [applied] policy service group [

service_group

]

show [applied] policy mac group [

mac_group

]

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments