manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1544 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1544

QoS Policy Commands

page 39-48

OmniSwitch CLI Reference Guide

November 2009

policy condition source network group

Associates a source network group with a policy condition.

policy condition condition_name source network group network_group

policy condition condition_name no source network group

Syntax Definitions

condition_name

The name of the condition.

network_group

The name of the source network group. Network groups are configured 
through the 

policy network group

 command. 

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

Use the 

no

 form of the command to remove a source network group from a condition; however, at least 

one classification parameter must be associated with a condition.

•

A source IP address and a source IP network group cannot be specified in the same condition.

Examples

-> policy condition cond5 source network group webgroup1

Release History

Release 6.6.1; command was introduced.

Related Commands

qos apply

Applies configured QoS and policy settings to the current configuration. 

policy condition

Creates a policy condition.

policy network group

Configures a network group name and its associated IP addresses. 

show policy condition

Shows information about policy conditions configured on the switch.

show policy network group

Displays information about policy network groups.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments