manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1274 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1274

RDP Commands

page 31-18

OmniSwitch 6250 CLI Reference Guide

November 2009

-> show ip router-discovery interface Marketing

Name

 = Marketing,

IP Address

= 11.255.4.1,

IP Mask

 = 255.0.0.0,

IP Interface status                     = Enabled,

RDP Interface status                    = Enabled,

Advertisement address                   = 224.0.0.1,

Max Advertisement interval              = 600 secs,

Min Advertisement interval              = 450 secs,

Advertisement lifetime                  = 1800 secs,

Preference Level                        = 0x0,

#Packets sent                           = 3,

#Packets received                       = 0,

Release History

Release 6.6.1; command was introduced.

output definitions

Name

The user-defined IP interface name defined at the time the IP interface 
was configured.

IP Address

The IP address associated with the IP interface name.

IP Mask

The subnet mask associated with the interface IP address.

IP Interface status

The IP status for this interface (

Enabled

 or 

Disabled

).

RDP Interface status

The RDP status for this interface (

Enabled

 or 

Disabled

).

Advertisement address

The destination address for RDP advertisement packets: 

224.0.0.1

 (all-

systems-multicast) or 

255.255.255.255

 (broadcast). Configured using 

the 

ip router-discovery interface advertisement-address

 command.

Max Advertisement interval

The maximum time, in seconds, RDP allows between each advertise-
ment packet the router transmits from this interface. Configured using 
the 

ip router-discovery interface max-advertisement-interval

 com-

mand.

Min Advertisement interval

The minimum time, in seconds, RDP allows between each advertise-
ment packet the router transmits from this interface. Configured using 
the 

ip router-discovery interface min-advertisement-interval

 com-

mand.

Advertisement lifetime

The maximum amount of time, in seconds, that router IP addresses 
advertised from this interface are considered valid. Configured using 
the 

ip router-discovery interface advertisement-lifetime

 command.

Preference Level

The preference level, displayed in hex, for each IP address advertised 
on this interface. Configured using the 

ip router-discovery interface 

preference-level

 command.

#Packets sent

The number of advertisement packets transmitted from this interface.

#Packets received

The number of solicitation packets received on this interface.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments