manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1771 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1771

IP Multicast Switching Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 41-53

ipv6 multicast query-response-interval

Sets the MLD query response interval on the specified VLAN or on the system if no VLAN is specified.

ipv6 multicast [vlan vid] query-response-interval [milliseconds]

Syntax Definitions

vid

VLAN on which to apply the configuration.

milliseconds

MLD query response interval in milliseconds. Valid range is 1 to 65535.

Defaults

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

IPv6 Multicast Switching and Routing must be enabled to set the MLD query response interval to use 
on the system and/or the specified VLANs.

•

If the MLD query response interval is already configured on the system, then the VLAN configuration 
will override the system's configuration.

•

The MLD query response interval refers to the time period to reply to an MLD query message.

•

To restore the MLD query response interval to its default (i.e., 10000 milliseconds) value on the 
system if no VLAN is specified, use 

ipv6 multicast query-response-interval

 followed by the value 0 

(e.g., ipv6 multicast query-response-interval 0) or use only 

ipv6 multicast query-response-interval 

(e.g., ipv6 multicast query-response-interval).

•

To restore the MLD last member query interval to its default (i.e., 10000 milliseconds) value on the 
specified VLAN, use 

ipv6 multicast vlan vid query-response-interval

 followed by the value 0 (e.g., 

ipv6 multicast vlan 2 query-response-interval 0) or use only

ipv6 multicast vlan vid query-response-interval 

(e.g., ipv6 multicast vlan 2 query-response-interval).

Examples

-> ipv6 multicast query-response-interval 20000

-> ipv6 multicast query-response-interval 0

-> ipv6 multicast query-response-interval

-> ipv6 multicast vlan 2 query-response-interval 20000

-> ipv6 multicast vlan 2 query-response-interval 0

-> ipv6 multicast vlan 2 query-response-interval

Release History

Release 6.6.1; command was introduced.

parameter

default

milliseconds

10000

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments