Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 621

Page: 621 / 2018

Loopback Detection Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 17-5

loopback-detection transmission-timer

Configures the LBD transmission timer on the switch.The transmission time is the time period between
the consecutive LBD packet transmissions.

loopback-detection transmission-timer seconds

Syntax Definitions

seconds

The time period in seconds between LBD packet transmissions. The
valid range is from 5 to 600 seconds.

Defaults

Platforms Supported

OmniSwitch 6250-Metro Models

Usage Guidelines

•

If the timer value is not configured, the default value of 30 seconds is assigned to the transmission
period.

•

The timer can be modified at any time. However, the new timer value will come into effect only after
the timer is restarted.

Examples

-> loopback-detection transmission-timer 200

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alaLdbConfigTable

alaLdbGLobalConfigTransmissionTimer

parameter

default

seconds

loopback-detection

Enables or disables LBD globally on the switch.

show loopback-detection

Displays LBD configuration information.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 621 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: