manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1252 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1252

IPv6 Commands

page 30-86

OmniSwitch 6250 CLI Reference Guide

November 2009

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alaRipngPeerTable

alaRipngPeerEntry

alaRipngPeerAddress

alaRipngPeerIndex

alaRipngPeerLastUpdate 

alaRipngPeerNumUpdates

alaRipngPeerBadPackets

alaRipngPeerNumRoutes

alaRipngPeerBadRoutes

output definitions

Address

IPv6 address of the peer.

Seen on Interface

Interface used to reach the peer.

Packets Recvd

Number of packets received from the peer.

Last Update

Number of seconds since the last update was received from the peer.

Peer address

Peer IPv6 address.

Received packets

Number of packets received from the peer.

Received bad packets

Number of bad packets received from the peer.

Received routes

Number of RIPng routes received from the peer.

Received bad routes

Number of bad RIPng routes received from the peer.

show ipv6 rip interface

Displays all or specified RIPng interface status.

show ipv6 rip routes

Displays all or a specific set of routes in RIPng Routing Table.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments