manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1499 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1499

QoS Policy Commands

OmniSwitch CLI Reference Guide

November 2009

page 39-3

Types of policies are generally determined by the kind of traffic they classify (policy conditions) and how 
the policy is enforced (policy actions). Commands used for particular types of policies are listed here. See 
the 

OmniSwitch 6250 Network Configuration Guide 

for more information about creating these types of 

policies and information about valid condition/action combinations.

Access Control Lists

policy condition
policy action disposition
policy rule

Traffic prioritization/shaping

policy action shared
policy action priority
policy action maximum bandwidth
policy action maximum depth
policy action cir
policy rule

802.1p/ToS/DSCP tagging or 
mapping

policy condition tos
policy condition dscp
policy condition 802.1p
policy action tos
policy action 802.1p
policy action dscp
policy rule

Network Address Translation 
(NAT)

policy condition source ip
policy condition source ipv6
policy rule

Policy based port mirroring

policy action mirror

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments