manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1568 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1568

QoS Policy Commands

page 39-72

OmniSwitch CLI Reference Guide

November 2009

policy condition service

Configures a service for a policy condition.

policy condition condition_name service service_name

policy condition condition_name no service

Syntax Definitions

condition_name

The name of the condition.

service_name

The service name, configured through the 

policy service

 command.

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

Use the 

no

 form of the command to remove a service group from a condition; however, at least one 

classification parameter must be associated with a condition.

•

A policy condition that specifies a service cannot also specify a service group, IP protocol, source IP 
port, or destination IP port.

Examples

-> policy condition cond12 service serv2

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alaQoSConditionTable

alaQoSConditionService

alaQoSAppliedConditionTable

alaQoSAppliedConditionService

policy service

Configures a service that may be used as part of a policy service group.

qos apply

Applies configured global QoS and policy settings to the current config-
uration (changes will be active and stored in flash). 

show policy service

Displays information about all particular policy services or a particular 
policy service configured on the switch.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments