manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 969 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 969

OmniSwitch 6250 CLI Reference Guide

November 2009

page 26-1

26   LINK OAM Commands

Ethernet in the First Mile (EFM), also known as LINK OAM, is a collection of protocols specified in 
IEEE 802.3ah, defining Ethernet in the access networks that connects subscribers to their immediate 
service provider. EFM, EFM-OAM and LINKOAM refers to IEEE 802.3ah standard.

LINK OAM (operation, administration, and maintenance) is a tool which monitors Layer-2 link status on 
the network by sending OAM protocol data units (OAMPDUs) between the network devices. OAMPDUs 
contain control and status information used to monitor, test and troubleshoot OAM-enabled links. By 
enabling LINK OAM on switch ports, network administators can monitor the link-related issues on the 
first mile. LINK OAM provides network administrators the ability to monitor link performance, remote 
fault detection and remote loopback control.   

Note. 

EFM (LINK OAM) does not include functions such as station management, bandwidth allocation or 

provisioning functions.

MIB information for the EFM (LINK OAM) commands is as

Filename:

 alcatel-ind1-dot3-oam-mib.mib 

Module:

 ALCATEL-IND1-DOT3-OAM-MIB

Filename:

 dot3-oam-mib.mib 

Module:

 DOT3-OAM-MIB

  

 

A summary of the available commands is listed here:

Global Configuration 
Commands

efm-oam
efm-oam multiple-pdu-count
efm-oam errored-frame-seconds-summary
efm-oam errored-frame-period

 

efm-oam errored-frame

Port Status Commands

efm-oam port status
efm-oam port mode
efm-oam port propagate-events

 

Port Event Notification 
Commands

efm-oam errored-frame
efm-oam errored-frame-period
efm-oam errored-frame-seconds-summary

 

Timer Interval Commands

efm-oam port keepalive-interval

 

efm-oam port hello-interval

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments