Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 692

Page: 692 / 2018

Ethernet Port Commands

page 20-20

OmniSwitch 6250 CLI Reference Guide

November 2009

interfaces max frame

Configures the maximum frame size for Gigabit Ethernet interfaces.

interfaces

slot[/port[-port2]] max frame bytes

Syntax Definitions

slot

Slot number you want to configure.

port

Port number of the interface you want to configure.

port2

Last port number in a range of ports you want to configure.

max frame

Maximum frame size, in bytes. Valid range is 1518–9216.

Defaults

Platforms Supported

OmniSwitch 6250

Usage Guidelines

N/A

Examples

-> interfaces 3/1 max frame 1518

-> interfaces 3 max frame 1518

-> interfaces 3/1-3 max frame 1518

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

esmConfTable

esmPortCfgMaxFrameSize

parameter

default

bytes

(Gigabit Ethernet Packets)

9216

bytes

(Ethernet Packets)

1553

show interfaces

Displays general interface information (e.g., hardware, MAC
address, input errors, and output errors).

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 692 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: