Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 225

Page: 225 / 2018

File Management Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 7-13

Examples

-> dir /certified

Listing Directory /certified:

drw 2048 Jul 8 11:05 ./

drw 2048 Aug 21 13:54 ../

-rw 3555538 Jul 5 09:37 Jeni.img

-rw 1824898 Jul 5 09:37 Jos.img

-rw 2929 Jul 5 09:37 Jrelease.img

-rw 10526922 Jul 5 09:37 Jbase.img

-rw 9393680 Jun 10 10:35 Jeni2.img

-rw 1452 Jun 28 18:23 boot.cfg

-rw 1348241 Jul 5 09:36 Jadvrout.img

-rw 2478362 Jul 5 09:37 Jdiag.img

-rw 349555 Jul 5 09:37 Jsecu.img

-rw 256 Jul 8 11:05 random-seed

2390016 bytes free

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

systemServices

systemServicesArg22

systemServicesAction

Changes the switch’s current working directory.

pwd

Displays the switch’s current working directory.

mkdir

Creates a new directory.

rmdir

Deletes an existing directory.

Displays the contents of a specified directory or the current working
directory.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 225 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: