manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1540 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1540

QoS Policy Commands

page 39-44

OmniSwitch CLI Reference Guide

November 2009

policy condition destination ipv6

Configures a destination IPv6 address for a policy condition.

policy condition condition_name destination ipv6 {any | ipv6_address [mask netmask]}

policy condition condition_name no destination ipv6 

Syntax Definitions

condition_name

The name of the condition.

any

Any destination IPv6 address.

ipv6_address

A specific destination IPv6 address.

netmask

The mask for the source IPv6 address.

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

Use the 

no

 form of this command to remove a destination IPv6 address from a condition; however, at 

least one classification parameter must be associated with a condition.

•

If a mask is not specified, the IPv6 address is assumed to be a host address.

Examples

-> policy condition cond3 destination ipv6 

::1234:531F:BCD2:F34A

Release History

Release 6.6.1; command was introduced.

Related Commands

qos apply

Applies configured QoS and policy settings to the current configuration. 

policy condition

Creates a policy condition.

show policy condition

Shows information about a particular policy condition configured on the 
switch.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments