Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 542

Page: 542 / 2018

Distributed Spanning Tree Commands

page 16-102

OmniSwitch 6250 CLI Reference Guide

November 2009

Examples

-> bridge mode flat

-> bridge cist 15 restricted-role on

-> bridge cist 8/23 root-guard disable

-> bridge mode 1x1

-> bridge cist 2/2 root-guard enable

-> bridge cist 10 restricted-role off

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

vStpInsPortTable

vStpInsPortNumber

vStpInsPortRestrictedRole

bridge mode

Selects the Spanning Tree operating mode (flat or 1x1) for the switch.

bridge 1x1 slot/port restricted-
role

Configures the restricted role status for a port or an aggregate of ports
for the 1x1 mode VLAN instance.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 542 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: