Home
/
Alcatel-Lucent
/
OmniSwitch 6250
/
Cli Reference Manual

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 777 / 2018

Share

Page: 777 / 2018

Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 777

Port Mobility Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 21-9

Related Commands

MIB Objects

vDhcpGenericRuleTable

vDhcpGenericRuleVlanId

vDhcpGenericRuleStatus

vlan dhcp port

Defines a DHCP port rule for an existing VLAN. The mobile port spec-
ified by this rule is temporarily assigned to the VLAN when it receives
DHCP frames.

vlan dhcp mac

Defines a DHCP MAC address rule for an existing VLAN. Mobile ports
that receive DHCP frames with a source MAC address that matches the
address specified by this rule are temporarily assigned to the VLAN.

vlan dhcp mac range

Defines a DHCP MAC address range rule for an existing VLAN.
Mobile ports that receive DHCP frames with a source MAC address that
falls within the range specified by this rule are temporarily assigned to
the VLAN.

Displays existing VLANs.

show vlan rules

Displays rules defined for VLANs.

«
...
775
776
777
778
779
...
»

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments