manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1789 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1789

IP Multicast Switching Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 41-71

show ip multicast

Displays the IP Multicast Switching and Routing status and the general configuration parameters on the 
specified VLAN or on the system if no VLAN is specified.

show ip multicast [vlan vid]

Syntax Definitions

vid

VLAN ID number (1–4094).

Defaults

By default the status and general configuration parameters for the system.

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

Specify a VLAN ID to display the configuration information for an individual VLAN.

Examples

-> show ip multicast

Status:                                       Enabled

Querying:                                     Disabled

Proxying Disabled

Spoofing:                                     Disabled

Zapping:                                      Disabled

Querier Forwarding:                           Disabled

Version:                                      2

Robustness:                                   2

Query Interval (seconds):                     125

Query Response Interval (tenths of seconds):  100

Last Member Query Interval(tenths of seconds):10

Unsolicited Report Interval(seconds):

1

Router Timeout (seconds):                     90

Source Timeout (seconds):                     30

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments